86-318-7669119
East Of Baoheng Road, Zhaobazhuang Section, Shenzhou, Hengshui, Hebei, China (Mainland)
| HL-2-2000 | HL-2-3000 | HL-2-4000 |
Wire diameter | Φ1.8-3.5mm | Φ1.8-3.5mm | Φ1.8-3.5mm |
Breadth | 500-2000mm | 500-3000mm | 500-4000mm |
Mesh | 50×50-70×70mm | 50×50-70×70mm | 50×50-70×70mm |
Efficiency | 80-100m2/h | 80-100m2/h | 80-100m2/h |
Motor power
| 4.8KW | 4.8KW | 4.8KW |
| 3800×2300×1500mm | 4800×2300×1500mm | 5800×2300×1500mm |
Put Web parts:
(1) must be used for three-phase four-wire 380V power supply
(2) open the box on the right switch, display, interface display maintenance staff contact information.
(3) by host boot key, press the "set" button, go to settings, display "check number" option begins to Flash, number by number keys to set the hook, press the "confirm" button to complete the setting. Then press the confirm key to enter "length" setting, and so on complete and several parameter settings and finally press "confirm" button to complete all settings.
(4) in a manual mode, fine-tune the host move completed check Center location, press the "cutter" button to complete the orientation began formal operation of the machine, servo motor speed does not affect the cutting angle.
(5) in the manual States the premise of the "reset" key, the number zero.
(6) the reduction in length, the grid reset, as described in the box comes with stickers.
(7) points in the manual State after moving into number of hooks, the machine is no longer running, press "reset button" reset the machine back to work.
Screw part:
(1) electrical box above press "Setup" steadily set parameters through the parameter is set to end on "confirm" to complete Setup. According to the triangle "down" key, the number 8 for automatic screw side, the number 9 is an online operation.
(2) electrical box top "manual" and "automatic", "cycle", "hook", "forward" and "reverse" or "hot networks" button.
Notes:
1. each reducer has oil, can be used directly.
2. the rotation direction of the motor shaft or arrow symbol on the wheel as standard.
3. before using the machine the joints into the lubricant (especially the cutter frame, that came with your copy of hinge inject lubricating oil at least once a day to ensure the life of the machine's health).
4. be sure to pay attention to safety, do not operate in the midst of cutting knife to avoid danger.
5. wear network part and side part of the wire and unscrew the join method, repair broken General gates for maintenance.
6. loosen the side part of the cone, chains, tight thread needles all need to pay attention to safety in the operation.
7. the machine must be grounded.
8. Thunder, rain must be off.
9. the wire into a steel eye must be random prototype randomly into the mold.
10. recommends using shiny galvanized wire and equipped with a SOAP solution to improve the speed and quality of the Web.
Shenzhou Hongli Gourp established in 1989. Registered capital of 100million yuan. Covering an area of more than 500mu.
2000-2010 for a decade our chain link fence production and processing industries, from the section of artificial mesh to a broken wire in automatic silk artificial webs, although the devices have improved but still cannot leave the manual. Artificially produced time-consuming and also improve the cost. After going through the manual is hard to find the stage that we have to find a way, one can get rid of artificial shortest way.
2011-2012 we began research exploration, fell has climbed up, twists, eventually 2013 we has has himself can weaving network of equipment, ARIMA automatically NC hook spent network machine, at this machine end has artificial weaving network of times, it of mechanical structure simple, weight light, accounted for to area small, used new frequency adjustable speed and the electric control clutch, maintenance simple, operation simple flexible, single can skilled operation more Zhang machine, so production efficiency greatly improve.
Single wire chain link fence machine appear automatically, is a great innovation in automated production chain link fence using wire mechanical automatic network technical, greatly saves manpower, overall stable performance, high production efficiency, the chain link fence entered a substantial automation of production times.
Shipping time : 5-7 work days after delivery
Shipping way : By sea ,By train
Shipping port : Tianjin port. Jingtang port . Caofeidian port
(1) about the sample
We can provide free samples, but the postage need customers to pay
(2) our ideas
Provide customers with quality products, the establishment of a complete set of quality management system and quality guarantee system, ensure better follow-up service for you
(3) the advantage of our strengths
Provide a small sample
High quality and affordable price quick delivery time
We have rich production experience
We have cooperate with many countries customers
Welcome to visit our factory at any time
